UW601 Underwater Concrete Crack Filler Epoxy Paste Repair

OverviewSpecsCoverage RateCureChemicalApplicationMore Options Underwater Crack Filler Epoxy Paste UW601 is a two component 100% solids epoxy gel designed for shallow repair of cracks and defects in concrete or masonry under water or on wet substrates on either vertical or horizontal surfaces. This product is easy to mix and has a non-critical mix ratio. Additionally, the product, because it is a 100% solids formulation, can be applied thicker on horizontal surfaces when required. This product can be used where contamination from water can occur during the cure process or it can be used directly underwater. Available in 3 gallon and 15 gallon kits.  ****SPECIAL ORDER ONLY – MIN ORDER QTY 60 GALLONS REQUIRED**** PRIMER: None required TOPCOAT: None required.  Where is Underwater Crack Filler Epoxy Used? Underwater or Wet Substrate Repairs Concrete & Masonry Surfaces Why UW601 Underwater Crack Filler Epoxy? Make Repairs Underwater or on Wet Surfaces Concrete and Masonry Both Horizontal & Vertical Repairs Good for Cracks up to 1/8″ and Thin Build Repairs 100% solids with 0 voc Low odor SPECIFICATIONS Solids By Weight 100%   By Volume 100% VOC 0 g/L Color Tan/Light Brown after mixing Recommended Thickness 1/8″ cracks or thin build repairs Coverage per Gallon 0.13 cubic feet or 1,228 lineal feet @1/8″ x 1/8″ Packaging 3 gallon kit, 15 gallon kit Mix Ratio 2:1 mix ratio by volume Shelf Life 12 months in unopened container Hardness Shore D = 65 Viscosity Mixed = 2,500,000 – 3,000,000 cps (typical)  Abrasion Resistance 31 mg loss with a 1000 gram total load at 1000 revolutions with a CS10 wheel Compressive Strength 9,400 psi (ASTM D695)  Flexural Strength 4910 psi (ASTM D-790)  Tensile Strength 4,102 psi (ASTM D-412)  Ultimate Elongation 2.3% at 70F  Gardner Variable Impactor 50 inch pounds direct – passed  Heat Deflection Temp 59 degrees C (138 degrees F)  Adhesion 405 psi dry and 350 psi wet (elcometer) – no delamination/concrete failure COVERAGE RATE Coverage Per Gallon 0.13 Cubic Feet Or 1,228 Lineal Feet @1/8″ X 1/8″ CURE SCHEDULE Pot Life – 1-1/2 gallon mix 20 – 30 minutes Tack free (dry to touch) 3 – 12 hours Recoat or topcoat 3 – 12 hours Light foot traffic 10 – 24 hours Full cure (heavy use) 2 – 7   days APPLICATION TEMPERATURE: Above 35-90 degrees F CHEMICAL RESISTANCE RATING  Butanol C  Ethyl alcohol C 1,1,1 Trichlorethane C  Methanol A  Xylene C  MEK A  Skydrol B  10% Sodium Hydroxide D  50% Sodium Hydroxide C  10% Sulfuric Acid C  70% Sulfuric Acid A  10% HCI C 5% Acetic Acid B Rating Key: A – Not Recommended, B – 2 Hour Term Splash Spill, C – 8 Hour Term Splash Spill, D – 72 Hour Immersion, E – Long Term Immersion. MIXING AND APPLICATION INSTRUCTIONS 1) PRODUCT STORAGE: Store product in an area so as to bring the material to normal room temperature before using. Continuous storage should be between 50-90°F. Avoid low temperatures and large temperature fluctuations in storage as these conditions could cause possible product crystallization. 2) SURFACE PREPARATION:  All dirt, foreign contaminants, oil contamination and laitance must be removed to assure a trouble free bond to the substrate. This product is intended for hairline cracks and other fractures up to an 1/8 inch in width. Remove all unsound concrete from within the crack to be repaired and thoroughly remove all debris from within the crack opening. 3) PRIMER: No primer is necessary. 4) PRODUCT MIXING:  This product has a mix ratio of 2 parts A to 1 part B by volume. To mix, simply measure out appropriate volumes of the material and mix them together thoroughly with slow speed mixing equipment such as a jiffy mixer, putty knife or spatula until the material is thoroughly mixed and uniform in color. Mix only an amount of material that can be used in the allotted pot life period. Improper mixing may result in product failure. For best mixing results and proper blending of parts A and B, recommend a Jiffy Mixer style drill mixer. Use of an improper drill mixer can result in streaking of the color because the pigment has not been thoroughly blended.  It can also create curing problems if the hardener also called activator (Part B) is not thoroughly blended with the resin (Part A) which can cause some areas on your floor to remain soft and not harden properly.  DO NOT USE A PAINT MIXER.  Many mixing problems described above can be traced back to using a paint mixer..  DO NOT HAND MIX as this approach can also result in the same problems as using a paint mixer. 5) PRODUCT APPLICATION:  The mixed material can be applied by marginal trowel, putty knife or any other suitable equipment. It is important to thoroughly work the paste into the repair area so as to displace any water from within the repair area. This product can be used underwater as well as in any area where the flow of water cannot be controlled. 6) RECOAT OR TOPCOATING:  For underwater repairs, we do not recommend any topcoat be applied. However, in areas where water contamination may occur during the cure process but subsequent to topcoat application, our NP600L can be used effectively. See the technical data for the NP600 before using or contact your sales representative for further details. Allow the NP601 to become tack free prior to topcoating. Multiple coats of the NP601 are acceptable and bond readily. 7) SURFACE CLEANING:  Caution! Some cleaners may affect the color of the fast set gel installed. Test each cleaner in a small area, utilizing your cleaning technique. If no ill effects are noted, you can continue to clean with the product and process tested. 8) RESTRICTIONS:  Restrict the use of the floor to light traffic and non-harsh chemicals until the coating is fully cured (see technical data under full cure). It is best to let the floor remain dry for the full cure cycle. Dependent on actual complete system application, surface may be slippery, especially when wet or contaminated; keep surface clean and dry. LIMITATIONS: Color stability may be affected by environmental conditions such as immersion service, temperature, or chemical exposure. Colors may vary from batch to batch. This product is not UV color stable and will discolor when exposed to UV rays or some indoor lighting such as sodium vapor lights. All new concrete must be cured for at least 30 days prior to application. It is advisable to place test patches prior to undertaking underwater or water  contaminated repairs  to insure product and surface compatibility. The temperature of the water may increase or decrease the time for the material to cure,  dependent on the temperature of the water. Physical properties listed on this technical data sheet are typical values and not specifications. NOTICE TO BUYER: DISCLAIMER OF WARRANTIES AND LIMITATIONS ON OUR LIABILITY We warrant that our products are manufactured to strict quality assurance specifications and that the information supplied by us is accurate to the best of our knowledge. Such information supplied about our products is not a representation or a warranty. It is supplied on the condition that you shall make your own tests to determine the suitability of our product for your particular purpose. Any use or application other than recommended herein is the sole responsibility of the user. Listed physical properties are typical and should not be construed as specifications. NO WARRANTY IS MADE, EXPRESSED OR IMPLIED, REGARDING SUCH OTHER INFORMATION, THE DATA ON WHICH IT IS BASED, OR THE RESULTS YOU WILL OBTAIN FROM ITS USE. N0 WARRANTY IS MADE, EXPRESSED OR IMPLIED, THAT OUR PRODUCT SHALL BE MERCHANTABLE OR THAT OUR PRODUCT SHALL BE FIT FOR ANY PARTICULAR PURPOSE. NO WARRANTY IS MADE THAT THE USE OF SUCH INFORMATION OR OUR PRODUCT WILL NOT INFRINGE UPON ANY PATENT. We shall have no liability for incidental or consequential damages, direct or indirect. Our liability is limited to the net selling price of our product or the replacement of our product, at our option. Acceptance of delivery of our product means that you have accepted the terms of this warranty whether or not purchase orders or other documents state terms that vary from this warranty. No representative is authorized to make any representation or warranty or assume any other liability on our behalf with any sale of our products. Our products contain chemicals that may CAUSE SERIOUS PHYSICAL INJURY. BEFORE USING, READ THE MATERIAL SAFETY DATA SHEET AND FOLLOW ALL PRECAUTIONS TO PREVENT BODILY HARM.   6007 Wet Condition Epoxy For Concrete & Steel | Low Temp 35°F | 100% Solids From: $543.00 Protect Problem Wet and Damp Areas Withstands to 15-18 PSI Hydraulic Vapor Pressure Cold temperature down to 35°F Designed to Protect both Concrete and Steel Use as Primer With Topcoat or Floor Coating Offers Excelllent Moisture and Corrosive Protection with  Outstanding Adhesion 100% Solids, no VOC, 2 Component Select options This product has multiple variants. The options may be chosen on the product page Bio-Chime E390 Joint Sealant & Flexible Coating | Expansion Joints | Apply to 2″ Thick | ... From: $80.00 Tank Chime Area: Create a permanently flexible corrosion resistant seal on chime surfaces of storage tanks and similar structures Expansion Joints: Use in situations where other joint compounds would soften or fail by solvent or chemical attack. High resistance to weathering and UV exposure Flexible Coating: High flexibility without tearing allows for a durable, chip resistant coating for general applications Select options This product has multiple variants. The options may be chosen on the product page Bio-Dur E561 Epoxy Coating for Above Or Below Water Application | Heavy Duty | High Build 40-60 mils... From: $75.00 Advanced Protection: Safeguard surfaces against water and oil with hydrophobic and oleophobic properties. Easy Application: Apply effortlessly using a brush, roller, airless sprayer, or pump sprayer. Fast Drying: Achieve quick results with a fast drying time. Invisible Finish: Maintain the natural appearance of surfaces without altering their friction or slip resistance. Environmentally Friendly: Water-based formula with no solvents or VOCs, ensuring no unpleasant odors. Longevity: Enjoy up to 10 years of protection under suitable conditions. Versatile Use: Ideal for a variety of mineral substrates, ensuring vapor permeability without compromising surface integrity. Select options This product has multiple variants. The options may be chosen on the product page Bio-Fill E457 Epoxy Repair | Void Filler to 1″ | Chemical Resistant | Horizonal ,Vertical and ... From: $190.00 Civil Structures: Replacing concrete lost by impact or abrasion in power generation, transportation and port facilities Chemical Exposure: Restoration and protection of concrete exposed to chemical attack in sumps, secondary containment and similar areas 100% Solids VOC Free Strong yet lightweight filler Horizontal, Vertical and Overhead Applications Can be applied underwater Select options This product has multiple variants. The options may be chosen on the product page Create-A-Quartz-Blend & Solid Color Granules for Epoxy, Polyaspartic Coatings | 47 Colors From: $3.00 Choose from 47 solid colors for single color floor OR Create-A-Blend option for your own unique color mix Natural looking Decorative Appearance Use outdoor with superior colorfast / UV stability Extreme abrasion resistance Excellent chemical resistance Great for high traffic, heavy-duty environments Outstanding slip-resistance qualities Extraordinary resilience Grain Size 40-S Broadcast Grade (40 mesh, spherical - MOST POPULAR SIZE) Grain Size 25-A Trowel Grade (25 mesh, angular) USE OUR COLOR VISUALIZER  TO SEE WHAT YOUR QUARTZ GRANULES WILL LOOK LIKE SOLD IN 50 LB BAGS HOLIDAY SHIPPING SURCHARGES MAY APPLY WEST OF MISSISSIPPI Select options This product has multiple variants. The options may be chosen on the product page E155CL Damp Condition Clear Epoxy Primer | Moisture Tolerant | Quick Cure | Low Temp 45° | Flexible From: $60.00 May be Applied to Damp or Moist Concrete Surfaces Excellent as a tough, flexible and clear concrete primer and sealer When used as clear Concrete Sealer has very low permeability to keep water and chemicals out while reducing concrete dusting, spalling and deterioration Excellent Adhesion to Concrete Excellent Primer for use with high performance coating systems As Quick as 30 min Recoat Time for 100% Solids Epoxy Systems Significantly Reduces Chance of Concrete Outgassing Problems Easy concrete preparation with either acid etching or concrete diamond grinding Select options This product has multiple variants. The options may be chosen on the product page E591 / E590 Wet Surface Epoxy | Apply Underwater | Cures to 35°F | Concrete – Steel | Floors &... From: $120.00 May be applied on wet or under water surfaces Cold temperature application down to 35°F Self-priming on steel and on most concrete applications Ideal for marginally prepared and painted surfaces Outstanding impact and abrasion High film build - Up to 20 mil DFT per coat on horizontal surfaces Vertical surfaces to 12 mils Excellent coating for manholes 100% solids and 0 g/L VOC's 3 Colors Available Select options This product has multiple variants. The options may be chosen on the product page HyperBOND Epoxy | Wet Condition Moisture Tolerant | Concrete Floor Coating | Low Temp 40F | 100% Sol... From: $60.00 Tough, Durable Epoxy Coating Outstanding Bonding Water Insensitive and Can Be Applied In Wet Conditions Withstands up to 9 lbs. of hydrostatic pressure Cold temperature application down to 40F Long 30-35 min working time Resistant to Blushing/Sweating Good chemical, impact and abrasion resistance High solids 100% Available in clear & 12 colors! (Pigment sold separately).  In 3 gallon kits only, available pre-colored in 3 colors Select options This product has multiple variants. The options may be chosen on the product page Hot Mend-Con RTU Concrete Repair | Wet Conditions & Underwater | Vertical No Sag | Quick Cure | Pai... $470.00 Repair in Wet conditions - Apply Underwater Great for Pool Repairs High strength epoxy Bonds to fresh or hardened concrete, stucco, wood, metal No Sag No Drip Formula - perfect for Vertical, Overhead or Horizontal surfaces Quick Cure Dries to touch 15 minutes, paint in 1 hour and drive on it in 8 hours (temperature dependent) 2x as strong as most concrete - Compressive strength 8000 psi Easy To Apply – Convenient ready-to-use cartridge system Wide application temperature 40°F – 100°F Paintable surface Comes in Case of 12 Cartridges & Cartridge Gun Select options This product has multiple variants. The options may be chosen on the product page P3 Marine | Saltwater, Fresh Water & Chloride Concrete Protection | Waterproofs | Permanent Sal... $700.00 Exceptional Marine Saltwater and Winter Road Salt Chloride Concrete Waterproof Protection Great for Marine and Inland Waterway concrete infrastructure, docks, ramps, bridges, roads Easy Spray Apply Low Tide and Wet Concrete Horizontal & Vertical Increased Concrete Durability and Life with 1x Permanent Application Using Silica Nano-Technology Reduces Depth of Penetration of Water Under Pressure 90% EN 12390-8 Improved resistance to Chloride Penetration For Long Term Durability 26% NT-492 (new alt to ASTM C1202) Withstands Min 75lbs Hydrostatic Vapor Pressure Resistance to Concrete Freeze / Thaw damage increased 48% ASTM C666 Excellent Protection Against Salt Corrosion, Improved 51% ASTM C1556 Deep Penetration to 3″ Protects from Inside Out For Exceptional Results Improved abrasion resistance 58% ASTM C1803 Superior new concrete cure eliminates need for membrane, allows foot traffic 1 to 3 hours Zero VOC 15 Year Performance Warranty Available Select options This product has multiple variants. The options may be chosen on the product page Quartz Color Granule Blends for Epoxy, Polyaspartic Floor Coatings | 47 Color Blends From: $3.00 Wide Selection of 47 pre-mixed color blends Create-A-Blend - create your own unique blend from 43 solid colors Natural looking Decorative Appearance Use Outdoors - Superior colorfastness / UV stability Extreme abrasion resistance Excellent chemical resistance Great for high traffic, heavy-duty environments Outstanding slip-resistance qualities Extraordinary resilience Use outdoors with recommended non-yellowing polyaspartic topcoat Grain Size 40-S Broadcast Grade (40 mesh, spherical) Grade Size 25-A Trowel Grade (25 mesh, angular) USE OUR COLOR VISUALIZER  TO SEE WHAT YOUR QUARTZ GRANULES WILL LOOK LIKE SOLD IN 50 LB BAGS HOLIDAY SHIPPING SURCHARGES MAY APPLY WEST OF MISSISSIPPI Select options This product has multiple variants. The options may be chosen on the product page UW601 Underwater Concrete Crack Filler Epoxy Paste Repair $350.00 Make Repairs Underwater or on Wet Surfaces Concrete and Masonry Both Horizontal & Vertical Repairs Good for Cracks up to 1/8" and Thin Build Repairs Apply 35F - 90F 100% solids with 0 voc Low odor ****SPECIAL ORDER ONLY - MIN ORDER QTY 60 GALLONS REQUIRED**** Select options This product has multiple variants. The options may be chosen on the product page UW602 Underwater Pourable Concrete Crack Filler Epoxy Repair $325.00 Make Repairs Underwater or on Wet Surfaces Concrete, Cement and Masonry Both Horizontal & Vertical Repairs Good for Larger Cracks and Wide Variety of Repairs Easy to Use Pourable Formula 100% solids with 0 voc Low odor ****SPECIAL ORDER ONLY - MIN ORDER QTY 60 GALLONS REQUIRED**** Select options This product has multiple variants. The options may be chosen on the product page